Motor: Continuous-duty,
high starting torque motor with instant reverse and overload
protection. Available in 1/2, 3/4, and 1 and 1 1/2 HP;
single or three phase. Capacitor start on single phase.
Removable without affecting limit switch settings.
Drive Reduction:
10:1 first stage using heavy-duty gears
running in oil bath; cast iron housing; #41 chain second
stage; #41 chain on trolley.
Emergency
Disconnect: Spring-loaded
disconnect for emergency manual operation.
Wiring Type:
C2, B2, D1 and E2 wiring types are all
standard and easily selectable using the Logic Control Board
(L). T and TS wiring can be activated with the use of the
CPS II option board. Reversing Contactor Units (M) may have
C2 wiring standard and B2 available by simply moving a
jumper wire. All allstar garage door openers are pre-wired to accept a sensing
edge, photoelectric control, radio controls and most types
of access control equipment.
External Radio
Control Terminal: External
terminals provide quick, convenient connections for radio
controls.
Bearings: Sealed roller
bearings in gear reducer. Flange-mount industrial ball
bearings on drive shaft.
Clutch:
Heavy-duty torque limiter helps protect
against major damage to door and operator should the door
meet an obstruction.
Pushbutton Station:
3-button station for OPEN/CLOSE/STOP
functions is standard for all operators. Controls with one,
two and three buttons are available.
Construction:
allstar garage door opener NEMA 1 type
electrical box, heavy-duty 11-gauge steel frame with durable
powder coat finish, all reduction sprockets drilled and
pinned to shafts.
Rail Assembly:
High strength dual L-rail track with
exclusive nylon quiet gliding chain guides on rail spacers
for quiet, smooth operation. Includes heavy-duty wall mount
brackets for rail and operator.
Brake:
Solenoid-actuated brake is standard on 3/4
HP and higher.
Standard on the
GarageCreator® Logic Control (L):
Maintenance Alert
System: This important
feature provides an accurate method for tracking door use
and establishing safe and effective maintenance programs for
the door and the operator. The Maintenance Alert System
features and internal programmable cycle timer that actually
counts each time the door cycles. This system is easily
preset by the installer for the particular door and
application. Once the preset number is reached, an indicator
light on the 3-button station flashes to signal that it is
time for routine door and operator maintenance.
Maximum Run Timer:
This standard feature on the Logic Control
Board (L) is designed to protect against damage to the door
and operator. Simply set the system to auto learn the door's
standard cycle time. Any time a moving door takes 10 seconds
more than its programmed standard cycle time, the door will
automatically stop. The maximum run time for the default is
90 seconds. Delay-on-Reverse Circuit
Programmable
Mid-StopControl
Accessories and Options
Commercial Protector
SystemTM:
(Recommended) An inexpensive "non-contact"
photo safety sensor designed to sense an obstruction and
signal the allstar garage door opener to reverse to open.
Sensing Edge:
(Recommended) Designed to sense an
obstruction and signal door operator to stop or reverse as
desired. Either an electric or pneumatic sensing device can
be added to bottom edge of door.
Radio Control:
Portable transmitter signals allstar
garage door opener to
open and/or close door.
Bi-Parting Door
Hardware: Modification
includes hardware to use Model GSD on bi-parting door.
Key Switch:
Designed to restrict operation of door to
authorized personnel only. Various types available.
Available Plug-In
Option Boards for the Solid State Logic Control Board (L):
Commercial Protector
System® II:(Recommended)
Features our powerful photo sensors to provide a UL approved
self-monitoring operator for commercial door applications.
4-wire or 2-wire "fail-safe" edges may be used. Board also
contains a Timer-to-Close function.
Timer-to-Close
Option: Part of the CPS II
board. It provides the ability to close the door at a
programmable time from 5 seconds up to 1 hour. Combined with
the CPS II allstar garage door opener board for the convenience of a timer and the
safety necessary to protect an auto closing door.
Auxiliary Contact
Board Option: Features
both normally-open and normally-closed contacts that actuate
when unit is powered down. Can be used to signal security
systems, operate heaters, warning devices or other ancillary
devices (5V to 240V).
